To avoid prematurely blowing ATO style fuses or tripping breakers it is recommended the following rule-of-thumb be used to size fuses or breakers. This is especially important in lightbars with many LED modules running off a single fused source wire,. This Product contains high intensity LED devices. Lightbar LED modules are equipped with a low power "Dimming" mode as standard. For safety purposes, the corner modules in lightbars are not connected to the dimming circuit.
This ensures that when corner modules are turned on, full degree coverage and compliance with SAE warning light standards is provided. To disable the dimming function on a particular module, disconnect the white wires. The Dim setting reduces the light output of emergency warning lights reducing the effectiveness of them especially in brightly lit areas.
Failure to use adequate light for the circumstances can cause motorists to fail to see the emergency vehicle and lead to serious personal injury or death. The optic has been designed to exceed all applicable requirements for degree warning devices in Red, Blue, Amber and White. While the OPTIX will become the standard corner module for most configurations, the LED X corner module will still be available and may be required for some configurations.
Installation and Operation for both modules will be the same. Consult the factory for further information. Each degree corner module consists of a "master" and a "slave" driver circuit board, degree optics and LED light engines along with a single integrated heatsink bracket. The "master" circuit board rear position must always be powered for the "slave" front position to flash. The "master" is always located in the rear position of the module.
The lightbar is wired to allow running only the rear facing LED on each module by removing power to the front facing "slave" module. This gives a "front-cutoff" function. The flash pattern for each corner pair can be selected by shorting together the 2-pin header J1, on the "master" , momentarily and releasing.
The module is set-up for "Cycleflash" as a standard. Holding down the 2-pin header for 5 sec. The following chart describes the available patterns and order;. Both heads will be in the mode selected. Both heads will flash together unless in Front Cut-off mode. In addition to the warning modules the lightbar may be equipped with a number of single head. The flashing modules will have "Cycleflash" as the standard pattern. Table 2 shows the available patterns and the order when stepping through patterns.
The module can be reset to "Cycleflash" by shorting the header for greater than 5 seconds and releasing. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions.
Enter a new password. Code 3. Code 3 Excalibur User Manual Download for 1. Proper installation is vital to the performance of this warning device and the safe operation of the emergency vehicle.
Wiring Instructions read Carefully Before Installation. The mounting brackets must be placed so that the rubber feet are resting on the curved section of the roof, see Figure 2.
Once the light bar is centered, tighten the mounting bracket to the light bar. Apply the parking brake and release the brake pedal. Your mounting location avoid any moving vehicle parts or parts that. Installation tips for your excalibur remote start for honda and acura vehicles. The remote start should engage led flashing. Generate heat also avoid any sharp metal edges see. Excalibur water softeners and water conditioners remove the minerals that cause scale from the water entering the boiler.
Car Wash Spot-Free Rinse. A car wash spot-free rinse starts with the right water. Excalibur's line of commercial reverse osmosis systems remove the minerals that form spots when car wash rinse water evaporates, and operate at up to gallons per minute.
Water Hardness Solutions. A water softener will help you produce soft water. Port green wire function start pulse after start status dome light 6 sat. Standard, remote start, keyless entry, security system, comfort start the car again, then open the door and step on the brake pedal. This manual is available in your mobile. Have all remotes for the system at hand. It might be time to dust off the old, trusty manual. Enjoy remote start on a manual transmission vehicle, without performing the complex reservation.
Did you find these tips helpful?
0コメント