Do the same with any gaps between individual pieces as well. Try to make the caulk look as even and hidden as possible. When you're done, wipe up the excess with a damp rag.
Part 4. Spread a dab of wood putty to cover up nails. Wood putty comes in small containers or tubes. To apply it, all you have to do is pick up a small amount of putty with your finger, then press it onto the nail heads. Rub the putty to smooth it out and hide the nails. Use grit sandpaper to smooth out caulk and filler. Apply light pressure when sanding the quarter rounds to avoid scratching them. Go over the treated areas to blend them into the quarter rounds.
Touch them and look at them from a distance to make sure are well-blended. When you're done, wipe the quarter rounds with a damp rag to remove any debris. If you plan on painting or staining, consider sanding all of the quarter rounds. Paint the quarter rounds with a semi-gloss paint. Match the paint color to the color of the baseboards behind the quarter rounds.
Before opening the can of paint, protect the walls and floor by laying blue painter's tape around each quarter round.
Then, brush paint over the quarter rounds until they look clean and well-coated. Most paints take at least 4 hours to dry before you can improve the finish with a second layer. Some oil-based paints also stand out well on floor molding. Most experts use semi-gloss paint, which makes quarter rounds bright and easy to clean. Glossy paints are available, but they often make quarter rounds stand out from the walls too much.
If you plan on painting over wood quarter rounds, make sure your paint is designed to adhere to wood trim. Apply a wood stain for a natural natural look. Match the color of the staining product to the floor and any wood trim in the room. To apply the stainer, spread it over the quarter rounds with a brush or rag.
Wipe off the excess stain with a rag, then wait about 15 minutes before applying another coating. Continue doing this until the wood reaches the correct color. Oil and water-based stainers are the most common. Oil-based stains are easier to use and penetrate deeper, but water-based products tend to stain more evenly.
A lot of staining products take up to 24 hours to fully dry, so keep everyone away from the quarter rounds until then. Did you know you can get expert answers for this article? Unlock expert answers by supporting wikiHow. Abraham Schwartz Home Improvement Professional. Abraham Schwartz. Support wikiHow by unlocking this expert answer. Not Helpful 0 Helpful 0. Include your email address to get a message when this question is answered. By using this service, some information may be shared with YouTube.
Quarter rounds should be painted or stained before you install them. You may need to paint caulk and wood putty after the installation. Helpful 0 Not Helpful 0. Place cut quarter rounds on the wall before attaching them to test their fit. This is the way to lead up to a return: For the piece that will terminate in a return, lay down a piece of molding that is several inches longer than the length you need. Mark your cut point on the bottom of the molding, not the top. As before, lay down a light pencil mark to show your angle.
Cut the piece to a degree angle, then position and nail the piece into place. A return piece is a very short stub of trim that will fit into the angle at the end of the first piece. Position a second short piece of mitered trim against the wall with the mitered end matching the miter on the preceding piece. Cutting the tiny piece of return trim can be challenging, especially with a power saw, where the speed of the blade can break the small piece.
Instead, you may wish to make this cut with a manual miter box and saw. First, cut the small return piece at a degree angle across its end. Then, test-fit the return piece to make sure that it fits. If not, cut a new return piece. Nailing a return piece is not practical, as the wood will split when a nail is driven.
Instead, apply a tiny dot of wood glue to the mitered edge of the return piece where it meets the first piece. Do not glue the wall side or floor side of the return piece. Press the return piece in place so the mitered edges meet, and allow the pieces to sit undisturbed until the glue dries. Taping the pieces down with painter's tape will hold them in place while the glue cures. Pounding the nail head with a hammer will mar the trim. Instead, use a nail set and hammer to lightly tap on the nail heads until they are driven down just below the surface of the trim.
Remove the painter's tape from any glued return pieces. Touch up the paint or finish on the trim, if necessary. If there are small gaps between the molding pieces where the corners were slightly out of square, you can fill them with matching wood putty. With painted trim, you can use caulk to fill these gaps.
Actively scan device characteristics for identification. Use precise geolocation data. Select personalised content. Create a personalised content profile.
Measure ad performance. Select basic ads. Create a personalised ads profile. Select personalised ads. This method makes the process of nailing much easier and requires less effort and precision from the worker. Overall, however, it is similar to the previous method. The process is fairly simple:. When using quarter rounds, make sure you cut at the correct angles for corners and joints.
Incorrect angles can cause quarter rounds to protrude or look messy. For a regular degree angle you should cut your two molding pieces at degree angles at opposite sides, however for less sharp corners, for example, a degree corner, the angle will be halved to In addition, it is likely that despite cutting along the correct degrees, there is a minor gap between the two pieces.
This is usually the case when working on older baseboards which are likely to contract or expand with wear and tear. In such cases, use wood putty to fill the gaps. Quarter round molding comes in whole pieces from 6 to 12 ft 1. It is durable, does not have imperfections like wood, easy to install, and looks great!
We renovated mom's house, including installation of vinyl plank flooring. Quarter round moldings are installed against the existing baseboard. To understand the differences, you should know their similarities. Quarter round molding is used in many different applications, from the classic crown molding application to baseboard.
The purpose is usually caused by two reasons. One is the actual hardwood installation needs space to expand and contract. Then, brush the corners area and wipe along the wall edges of the room to get rid of dirt and debris. After you've marked the point where the molding needs to be cut, use a regular saw to create the cuts at the end opposite of the quarter.
This way there will be no joints, which can open up when the humidity changes and the pieces shrink. Diyers can avoid mistakes by cutting one piece at a time. We recently added vinyl plank flooring in our basement and will be Shoe molding vs quarter round. Cope and stick quarter round molding can be a challenge to install.
0コメント