To prevent electric shock, match wide blade of plug to wide slot and fully insert. The serial number is located on the rear of the unit. Refer to the attached sheet or the pages at the end of this manual for the information about each position of the parts.
OSD on-screen display menus that allow you to optimize this unit to suit your individual audiovisual system. In case the button names differ between the front panel and the remote control, the button name on the remote control is given in parentheses. Design and specifications are subject to change in part as a result of improvements, etc. In case of differences between the manual and product, the product has priority. Manufactured under license from Dolby Laboratories.
Manufactured under license under U. All Rights Reserved. Bluetooth is a registered trademark of the Bluetooth SIG and is used by Yamaha in accordance with a license agreement. Read the packaging carefully as these different types of batteries may have the same shape and color. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.
When the memory is cleared, insert new batteries, set up the remote control code and program any acquired functions that may have been cleared. The following steps describe the easiest way to enjoy DVD movie playback in your home theater. See pages 11 to 15 for.
Select magnetically shielded speakers. The minimum required speakers are two front speakers. The priority of the requirement of other speakers is as follows:. One or two surround back speaker s. Select a TV monitor, video monitor or projector equipped with a composite video input jack. You can also connect two subwoofers to this unit. In this case, prepare two active subwoofers and subwoofer cables. Cables are colored or shaped differently, perhaps with a stripe, groove or ridge.
Connect the striped grooved, etc. See page 28 for details. This unit is turned on. If you connect a Yamaha product that has capability of the SCENE control signals, this unit can automatically activate the component and start playback.
Refer to the instruction manual of the DVD player for further information. See page 22 for details. See page 27 for details. See pages 53 to 56 for tuning information. See page 37 for details. This unit is set to the standby mode and consumes a small amount of power in order to receive infrared signals from the remote control. The speaker layout below shows the speaker setting we recommend.
See page 14 for connection information. See page 13 for details. The front speakers are used for the main source sound plus effect sounds. Place these speakers at an equal distance from the ideal listening position. The distance of each speaker from each side of the video monitor should be the same.
The center speaker is for the center channel sounds dialog, vocals, etc. If for some reason it is not practical to use a center speaker, you can do without it.
Best results, however, are obtained with the full system. The surround back speakers supplement the surround speakers and provide more realistic front-to-back transitions. The use of a subwoofer with a built-in amplifier, such as the Yamaha Active Servo Processing Subwoofer System, is effective not only for reinforcing bass frequencies from any or all channels, but also for reproducing the high fidelity sound of the LFE low-frequency effect channel included in Dolby Digital and DTS sources.
You can connect one or two subwoofer s to this unit. When you use two subwoofers, you can enjoy deeper bass sound.
The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front speakers. Turn it slightly toward the center of the room to reduce wall reflections.
When you use two subwoofers, select the same type of the subwoofer as another and set these subwoofers as same sound characteristics. Place each subwoofer at the same distance from the listening position. SW FL. The functions and settings of each speaker are the same as those for the 7. For the smooth and unbroken sound field behind the listening position, place the surround left and right speakers farther back compared with the placement in the 7. You can enjoy multi-channel sources with sound field programs by using a speaker combination other than the 7.
The presence speakers supplement the sound from the front and surround back speakers with extra ambient effects produced by the sound field programs see page You can adjust the vertical position of dialogues with using the presence speakers see page If the connections are faulty, this unit cannot reproduce the input sources accurately. If this type of speaker still creates interference with the monitor, place the speakers away from the monitor.
For details about the speaker impedance setting, see page A speaker cord is actually a pair of insulated cables running side by side. Tighten the knob and then insert the banana plug connector into the end of the corresponding terminal.
Remove the shorting bars or bridges of your speakers to separate the LPF low pass filter and HPF high pass filter crossovers. This unit allows you to make bi-amplification connections to one speaker system. Check if your speakers support biamplification.
When you make the conventional connection, make sure that the shorting bars are put into the terminals appropriately. Refer to the instruction manuals of the speakers for details. This unit has three types of audio jacks. Connection depends on the availability of audio jacks on your other components. For conventional analog audio signals transmitted via left and right analog audio cables. Connect red plugs to the right jacks and white plugs to the left jacks.
Optical input jacks are compatible with digital signals with up to 96 kHz of sampling frequency. This unit has three types of video jacks. Connection depends on the availability of input jacks on your video monitor. For conventional composite video signals transmitted via composite video cables.
For S-video signals, separated into the luminance Y and chrominance C video signals transmitted on separate wires of S-video cables. For component video signals, separated into the luminance Y and chrominance P B , P R video signals transmitted on separate wires of component video cables. This unit is equipped with the video conversion function.
See pages 19 and 98 for details. Refer to the supplied instruction manuals for details. Doing so may disrupt playback or cause noise. Make sure that this unit and other components are unplugged from the AC wall outlets.
In this case, the HDMI indicator flashes irregularly. To record a source, make the same type of video connections between each component. However, you may hear less noise without the connection to the GND terminal for some turntables. This unit has more than enough power for any home use. However, if you want to add more power to the speaker output or if you want to use another amplifier, connect an external amplifier to the PRE OUT jacks.
Surround back channel output jacks. Be sure to match the left and right outputs to the left and right input jacks for the front and surround channels. We recommend that you connect at least a 5. Subwoofer out. Connect a Yamaha iPod universal dock or Bluetooth adapter to the DOCK terminal on the rear panel of this unit using its dedicated cable.
Be sure to turn down the volume of this unit and other components before making connections. Both FM and AM indoor antennas are supplied with this unit. Connect each antenna correctly to the designated terminals. In general, these antennas should provide sufficient signal strength.
If you experience poor reception quality, install an outdoor antenna. Consult the nearest authorized Yamaha dealer or service center about outdoor antennas. Use a 5 to 10 m 16 to 33 ft vinyl-covered wire extended outdoors from a window.
For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.
Use these 2 outlets to supply power to any connected components. Connect the power cable of your other components to these 2 outlets. Power to these 2 outlets is supplied when this unit is turned on. However, power to these 2 outlets is cut off when this unit is turned off. When this unit completes charging or the iPod is disconnected, the power is cut off automatically when this unit is in the standby mode.
The memory back-up circuit prevents the stored data from being lost even if this unit is in the standby mode. However, the stored data will be lost in case the power cable is disconnected from the AC wall outlet or if the power supply is cut off for more than one week. This unit turns on, and the advanced setup menu appears in the front panel display. In the standby mode, this unit consumes a small amount of power in order to receive infrared signals from the remote control.
Lights up when the adaptive dynamic range control feature is turned on see page See page 16 for details. See page 19 for details. See pages 37 to 39 for the tuning information.
This unit is set to the standby mode. In the standby mode, this unit consumes a small amount of power in order to receive infrared signals from the remote control. The speaker layout below shows the speaker setting we recommend. The front speakers are used for the main source sound plus effect sounds. Place these speakers at an equal distance from the ideal listening position. The distance of each speaker from each side of the video monitor should be the same.
The center speaker is for the center channel sounds dialog, vocals, etc. If for some reason it is not practical to use a center speaker, you can do without it. Best results, however, are obtained with the full system. The use of a subwoofer with a built-in amplifier, such as the Yamaha Active Servo Processing Subwoofer System, is effective not only for reinforcing bass frequencies from any or all channels, but also for high fidelity sound reproduction of the LFE low-frequency effect channel included in Dolby Digital and DTS sources.
The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front speakers. Turn it slightly toward the center of the room to reduce wall reflections. If the connections are faulty, this unit cannot reproduce the input sources accurately. If this type of speakers still creates the interference with the monitor, place the speakers away from the monitor. A speaker cord is actually a pair of insulated cables running side by side.
Cables are colored or shaped differently, perhaps with a stripe, groove or ridges. The banana plug is a single-pole electrical connector widely used to terminate speaker cables. First, tighten the knob and then insert the banana plug connector into the end of the corresponding terminal. Black: negative —. This unit turns on, an the advanced setup menu appears in the front panel display.
This unit has three types of audio jacks. Connection depends on the availability of audio jacks on your other components. For conventional analog audio signals transmitted via left and right analog audio cables. Connect red plugs to the right jacks and white plugs to the left jacks. All digital input jacks are compatible with digital signals with up to 96 kHz of sampling frequency. This unit has two types of video jacks. Connection depends on the availability of input jacks on your video monitor.
For conventional composite video signals transmitted via composite video cables. For component signals, separated into the luminance Y and chrominance P B , P R video signals transmitted on separate wires of component video cables. Audio signals input at the HDMI jack are not output from any speaker terminals but output from the connected video monitor. You can play back pictures by connecting your video monitor and video source component to this unit using HDMI connections.
Refer to the instruction manual of each connected component. Make sure that this unit and other components are unplugged from the AC wall outlets. Be sure to connect your video components in the same way you connect your video monitor to this unit. Be sure to match the left and right output jacks to the left and right input jacks for the front and surround channels. We recommend that you connect a 5. Connect a Yamaha iPod universal dock or Bluetooth adapter to the DOCK terminal on the rear panel of this unit using its dedicated cable.
Be sure to turn down the volume of this unit and other components before making connections. Both FM and AM indoor antennas are supplied with this unit. In general, these antennas should provide sufficient signal strength. Connect each antenna correctly to the designated terminals. If you experience poor reception quality, install an outdoor antenna. Consult the nearest authorized Yamaha dealer or service center about outdoor antennas. For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground.
A good earth ground is a metal stake driven into moist earth. The types of the supplied AM loop antenna is different depending on the models. Once all connections are complete, plug the power cable into the AC wall outlet. Power cable. When you turn on this unit, there will be a 4 to 5-second delay before this unit can reproduce sound.
Lights up when headphones are connected and a sound field program is selected see page The corresponding cursor lights up to show the currently selected input source. Shows the name of the current sound field program and other information when adjusting or changing settings.
Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation, e If the product has been dropped or damaged in any way, and f When the product exhibits a distinct change in perfor- mance - this indicates a need for service.
Getting started. Preparation: Check the items Prepare the following items. Speakers Front speaker The minimum required speakers are two front speakers. Active subwoofer Speaker cable Page Advanced Setup Advanced setup This unit has additional menus that are displayed in the front panel display.
The advanced setup menu offers additional operations to adjust and customize the way this unit operates. Play a source whose signals can be reproduced by this unit. Remedy page — — Page 83 Problem The sound suddenly The protection circuitry has been activated goes off. The sleep timer has turned off this unit. The sound is muted. Sound is heard from Incorrect cable connections.
Dolby Digital signals. There is distortion, and There is multi-path interference. In this case, read the cause and follow the corresponding remedies. Optimizer microphone is not connected. Unplug HP! Headphones are connected. SP A surround channel signal is not detected. Remedy page Direct sunlight or lighting from an inverter type of fluorescent lamp, etc. The batteries are weak. The remote control code is not correctly set. Parameters for headphones have been set for each sound field so that accurate representations of all the sound field programs can be enjoyed on headphones.
Page 97 XM Radio setting, Option menu Page Tandy , , , Weltblick , Weston Tashiko , , White Westinghouse Tatung , , , , , Yamaha , Teac Yamishi , , , Yoko Techwood , Teknika , , , This manual is also suitable for: Htrbl. Print page 1 Print document pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Sign up!
0コメント